Home / Solutions / Cable Joint and Distribution Cabinet Contact Temperature Measurement

Cable Joint and Distribution Cabinet Contact Temperature Measurement

Cable joint and distribution cabinet contact temperature measurement should deploy points around specific heat-generating parts, using EST temperature products and confirmed sensors to collect temperature, and obtaining same-circuit current through SFA, ESX aggregation, and platform display. The focus is not on measuring the average in-cabinet temperature, but on establishing the correspondence between contacts, circuits, loads, and alarms. The probe type, range, installation/fixing method, insulation distance, and number of channels must be confirmed based on the specific model and on-site cabinet structure.

Electrical HazardsStatus Visualization

Solution overview

The solution applies to locations prone to heating due to poor contact or load changes, such as cable terminals, busbar connections, breaker contacts, and key terminals, providing continuous temperature trends and anomaly alarms.

Applicable industries

  • Industrial and Commercial Power Distribution

Primary user roles

  • Electrical Operations and Maintenance
  • Safety Management Personnel
  • Design Institute

Problems addressed

  • Overheating of cable joints and contacts often requires outage inspection, with a lack of continuous temperature data in daily operation.
  • Measurement points are scattered and in-cabinet electromagnetic and wiring conditions are complex, making it difficult to correlate temperature anomalies with specific circuits.

Recommended product combination

FEXLINK

FEXLINK IoT Platform

Display measurement points, circuits, trends, alarms, and handling records.

System architecture and data flow

Cable Joint and Distribution Cabinet Contact Temperature Measurement System TopologyFour-layer data flow across perception, edge control, platform and application for Cable Joint and Distribution Cabinet Contact Temperature Measurement.01Perception layer
Temperature sensors are installed near cable joints, terminals, or contacts, and EST collects the temperatur…
02Edge / control layer
ESX aggregates temperature with same-circuit current data and executes on-site rules.
03Platform layer
FEXLINK displays temperature rise trends by cabinet, circuit, and measurement point.
04Application layer
O&M personnel arrange infrared re-check, outage inspection, or maintenance based on alarms and trends.

Perception layer

Temperature sensors are installed near cable joints, terminals, or contacts, and EST collects the temperature of each channel.

Edge / control layer

ESX aggregates temperature with same-circuit current data and executes on-site rules.

Platform layer

FEXLINK displays temperature rise trends by cabinet, circuit, and measurement point.

Application layer

O&M personnel arrange infrared re-check, outage inspection, or maintenance based on alarms and trends.

Data flow

  1. EST collects cable joint and contact temperature.
  2. SFA collects the current or load of the corresponding circuit.
  3. ESX aggregates and establishes the relationship between measurement points and circuits.
  4. The platform displays trends, alarms, and handling status.

Integration and interfaces

  • In-cabinet layout, terminal location, cable routing, and installable space must be provided.
  • The temperature probe fixing method, insulation distance, temperature resistance, and anti-interference conditions must be confirmed.
  • The platform must maintain a unique correspondence between cabinet number, circuit number, and measurement point number.

Applicable standards

  • GB 50054, the GB/T 16895 series, and standards related to temperature rise of low-voltage switchgear assemblies; the final version and measurement point requirements are to be confirmed by the project.

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Verify joint location, temperature channel, and platform point point by point.
  • Verify temperature readings, offline status, and alarm records.
  • Verify the correlation between temperature and current data under the same circuit.
  • Deliver the measurement-point diagram, installation records, configuration files, and acceptance records.

Limitations and exclusions

  • The in-cabinet ambient temperature cannot be directly used as the contact temperature.
  • Temperature records cannot replace joint tightening, torque checks, or outage preventive tests.
  • Specific probe temperature resistance, accuracy, installation accessories, and protection conditions need to be confirmed by the model documentation.

Operational value

  • Supplement continuous temperature records for scattered contacts.
  • Help detect abnormal temperature rise related to load changes.
  • Reduce interval blind spots caused by relying solely on periodic infrared inspection.

Selection guidance

  • First select contact or adapted temperature measurement based on the measurement point structure, then determine the EST channels and probes.
  • Decide on a wired or wireless solution based on in-cabinet wiring and shielding conditions.
  • When correlation judgment is required for the same circuit, electrical-parameter collection should be configured at the same time.

Typical implementation patterns

  • A typical implementation model is to list a high-risk joint inventory by cabinet, install temperature sensors point by point, and use the same circuit's current as a trend correlation variable. This description does not imply that a specific project has achieved a particular diagnostic result.

Before retrofit → With the solution

Before retrofit

  • Overheating of cable joints and contacts often requires outage inspection, with a lack of continuous temperature data in daily operation.
  • Measurement points are scattered and in-cabinet electromagnetic and wiring conditions are complex, making it difficult to correlate temperature anomalies with specific circuits.

With the solution

  • Supplement continuous temperature records for scattered contacts.
  • Help detect abnormal temperature rise related to load changes.
  • Reduce interval blind spots caused by relying solely on periodic infrared inspection.

How to evaluate the effect

01

Measurable signal

Temperature sensors are installed near cable joints, terminals, or contacts, and EST col…

02

Data source

EST Multi-Channel Temperature Monitoring Module · SFA Multi-Parameter Electrical Controller

03

Review method

Verify joint location, temperature channel, and platform point point by point.

04

Acceptance boundary

The in-cabinet ambient temperature cannot be directly used as the contact temperature.

Frequently asked questions

Which locations are most suitable for arranging temperature measurement points?

Typically, priority is given to cable terminals, main busbar connections, breaker contacts, key terminals, and historical heating points, with the final decision made by on-site risk assessment.

Is it acceptable to measure only temperature without current?

Independent temperature alarms can be achieved, but the lack of load context is not conducive to judging whether temperature rise is related to operating current.

Will the system handle it automatically after contact temperature rises?

By default, only monitoring and alarming are provided. For interlocking, control logic, permissions, and a failure strategy must be designed separately.

Can the probe be attached directly to a live conductor?

It must be determined based on product installation requirements, insulation distance, and on-site electrical safety regulations; applicability cannot be assumed on one's own.

How to avoid confusion in measurement point numbering?

Establish a one-to-one correspondence table of cabinet number, circuit number, phase, measurement point number, and device channel, and verify point by point during acceptance.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK