Home / Solutions / Test Cabinet and Burn-in Room Safety Monitoring

Test Cabinet and Burn-in Room Safety Monitoring

Test cabinet and burn-in room safety monitoring should adopt a layered architecture of local collection, local rules, and optional remote O&M. ESF can monitor residual current and temperature; EST is used to extend temperature measurement points; ESX aggregates data and executes on-site rules; when necessary, audible and visual alarms or power-cutoff interlocks are formed through confirmed PLC I/O, relays, and HMI. Smoke detection, grounding, emergency stop, and fire signals may come from third-party devices and cannot be replaced by existing product names by default; all control circuits must retain independent emergency stop, manual reset, and fail-safe design.

Electrical HazardsStatus Visualization

Solution overview

The solution targets long-running and unattended test stations, prioritizing local visibility, alarming, and safe handling, then considering platform remote management.

Applicable industries

  • Industrial and Commercial Power Distribution

Primary user roles

  • Electrical Operations and Maintenance
  • Safety Management Personnel
  • Design Institute

Problems addressed

  • Temperature, leakage current, smoke detection, and station status are scattered, with anomalies relying on on-site personnel to discover.
  • Remote platform alarms cannot directly meet local power cutoff, audible/visual, and emergency-stop requirements.

Recommended product combination

FEXLINK

FEXLINK IoT Platform

Display station status, alarms, historical records, and remote O&M information.

System architecture and data flow

Test Cabinet and Burn-in Room Safety Monitoring System TopologyFour-layer data flow across perception, edge control, platform and application for Test Cabinet and Burn-in Room Safety Monitoring.01Perception layer
ESF, EST, and third-party sensors collect temperature, leakage current, smoke detection, grounding, and emer…
02Edge / control layer
ESX executes alarm rules;when hard interlock is needed, it is completed by a reviewed PLC or relay circuit.
03Platform layer
FEXLINK aggregates stations, events, and handling records.
04Application layer
On-site audible/visual alarms, power-cutoff isolation, manual reset, and remote notification collaborate acc…

Perception layer

ESF, EST, and third-party sensors collect temperature, leakage current, smoke detection, grounding, and emergency-stop status.

Edge / control layer

ESX executes alarm rules; when hard interlock is needed, it is completed by a reviewed PLC or relay circuit.

Platform layer

FEXLINK aggregates stations, events, and handling records.

Application layer

On-site audible/visual alarms, power-cutoff isolation, manual reset, and remote notification collaborate according to safety procedures.

Data flow

  1. On-site sensors collect temperature, leakage current, and switching quantities.
  2. ESX or the control layer judges according to rules and triggers local alarms.
  3. When power cutoff is needed, it is executed through the safety circuit and status is fed back.
  4. The platform records events, handling, and recovery.

Integration and interfaces

  • Station electrical diagrams, emergency-stop circuits, smoke-detection interfaces, loads, and power-cutoff strategies must be provided.
  • The power supply, isolation, and communication of ESX, PLC I/O, relays, and HMI must be confirmed.
  • The boundary between software alarms and hard safety circuits must be clarified.

Applicable standards

  • Applicable project-specific standards for low-voltage power distribution, electrical fire monitoring, and equipment safety; the final version and control circuit requirements are to be confirmed by the project.

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Verify sensors, I/O, HMI, and platform points station by station.
  • Verify local audible/visual alarms, remote notification, and power-cutoff interlock.
  • Test emergency stop, manual reset, communication interruption, and power recovery.
  • Deliver the control logic, wiring diagrams, point list, and acceptance records.

Limitations and exclusions

  • Current documentation does not prove the company's own smoke detectors, gas detectors, or all emergency-stop devices.
  • The monitoring platform cannot replace emergency-stop, fire protection, equipment safety, and personnel protection systems.
  • Power-cutoff interlock and automatic recovery must undergo specialized verification according to device risk and on-site regulations.

Operational value

  • Combine station safety status with local handling.
  • Provide continuous monitoring for long-running burn-in rooms.
  • Unify local alarms with remote O&M records.

Selection guidance

  • First determine whether only alarming is needed, or whether local power cutoff and safety interlock are required.
  • When hard interlock is needed, select a reviewed PLC, relay, and safety circuit; do not replace it with pure software rules.
  • Configure terminals based on temperature measurement points, leakage circuits, and I/O count.

Typical implementation patterns

  • A typical implementation model is to establish independent circuits and alarm points for each test station, first implement temperature, leakage, and switching-quantity collection, then connect to local power cutoff and the platform through controlled integration testing. This description does not represent that a specific station has been accepted.

Before retrofit → With the solution

Before retrofit

  • Temperature, leakage current, smoke detection, and station status are scattered, with anomalies relying on on-site personnel to discover.
  • Remote platform alarms cannot directly meet local power cutoff, audible/visual, and emergency-stop requirements.

With the solution

  • Combine station safety status with local handling.
  • Provide continuous monitoring for long-running burn-in rooms.
  • Unify local alarms with remote O&M records.

How to evaluate the effect

01

Measurable signal

ESF, EST, and third-party sensors collect temperature, leakage current, smoke detection,…

02

Data source

ESF Electrical Fire Monitoring Module · EST Multi-Channel Temperature Monitoring Module · ESX-0223-GR Edge Computing Gateway (4G Uplink)

03

Review method

Verify sensors, I/O, HMI, and platform points station by station.

04

Acceptance boundary

Current documentation does not prove the company's own smoke detectors, gas detectors, or all emergency-stop devices.

Frequently asked questions

Can ESX directly undertake emergency-stop safety functions?

Cannot be used in this way by default. Emergency stop and safety interlock should be implemented by an independent safety circuit that meets requirements.

How are smoke detection and grounding status integrated?

Usually integrated through dry contacts of third-party devices or explicit protocols; the interface and power supply conditions need to be confirmed.

Will local alarms still work after network disconnection?

Local alarms can be achieved through reasonable local rules and device configuration, but must be explicitly verified in the solution and acceptance.

Is automatic power restoration safe?

Should not restore automatically by default. Whether it is permitted and the restoration conditions must be designed in combination with device risk, manual confirmation, and on-site regulations.

What roles do HMI and the platform respectively undertake?

HMI is for on-site operation and status viewing; the platform is for cross-station management and historical records; the two should have separate permissions and responsibilities.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK