Home / Solutions / Full Electrical Quantity Intelligent Monitoring for Low-Voltage Distribution Rooms

Full Electrical Quantity Intelligent Monitoring for Low-Voltage Distribution Rooms

Full electrical quantity intelligent monitoring for low-voltage distribution rooms should be based on a circuit inventory, select SFA multi-element measurement-and-control terminals and ESE power-quality monitoring products according to monitoring objectives, then aggregate by ESX and integrate with FEXLINK. SFA can assume corresponding functions among confirmed electrical parameters, residual current, temperature and switching quantities; ESE is used for power-quality analysis supported by the confirmed model. Different models differ in current-integration method, accuracy, harmonic capability and I/O configuration, so before designing the scheme, selection must be carried out item by item based on the circuit list, CT conditions and technical datasheet.

Electrical HazardsFull Electrical Parameters

Solution overview

This scheme unifies the electrical parameters, trends and alarms of incoming, bus-tie, feeder and key circuits into a distribution-room view, and applies to new construction and phased retrofit.

Applicable industries

  • Industrial and Commercial Power Distribution

Primary user roles

  • Electrical Operations and Maintenance
  • Safety Management Personnel
  • Design Institute

Problems addressed

  • Voltage, current, power, energy and state data of different cabinets and circuits are scattered and cannot be viewed in a unified way.
  • Three-phase imbalance, harmonics and load changes lack continuous trends, and troubleshooting relies on on-site measurement.

Recommended product combination

FEXLINK

FEXLINK IoT Platform

Forms a hierarchical view of distribution room, cabinet, circuit and alarms, supporting historical data analysis.

System architecture and data flow

Full Electrical Quantity Intelligent Monitoring for Low-Voltage Distribution Rooms System TopologyFour-layer data flow across perception, edge control, platform and application for Full Electrical Quantity Intelligent Monitoring for Low-Voltage Distribution Rooms.01Perception layer
SFA and ESE acquire circuit electrical parameters in the cabinet;the integration method is determined by dir…
02Edge / control layer
ESX aggregates multiple terminal data, completing protocol conversion, caching and edge alarms.
03Platform layer
FEXLINK uniformly displays the distribution room, cabinets, circuits, real-time values and historical trends…
04Application layer
O&M personnel view key circuits by alarm and trend, and designers can review load and power quality based on…

Perception layer

SFA and ESE acquire circuit electrical parameters in the cabinet; the integration method is determined by direct integration or CT conditions.

Edge / control layer

ESX aggregates multiple terminal data, completing protocol conversion, caching and edge alarms.

Platform layer

FEXLINK uniformly displays the distribution room, cabinets, circuits, real-time values and historical trends.

Application layer

O&M personnel view key circuits by alarm and trend, and designers can review load and power quality based on records.

Data flow

  1. The terminal acquires configured parameters such as voltage, current, power and energy of each circuit.
  2. ESX aggregates device data by cabinet or area.
  3. Data is uploaded to the platform and associated with the device inventory.
  4. The platform performs display, alarms, reports and historical queries.

Integration and interfaces

  • Provide single-line diagrams, circuit lists, CT ratios, in-cabinet space and communication routes.
  • Confirm the RS485 address, network method, platform point list and existing monitoring interface.
  • If integrating with a third-party system, agree on data direction, refresh cycle and fault handling according to the point list.

Applicable standards

  • GB 50054, the GB/T 16895 series and power-quality standards applicable to the project; the final version and index requirements are confirmed by the project.

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Verify the circuit list, device model, CT ratio and installation location.
  • Compare on-site readings, terminal displays, and platform data point by point.
  • Verify three-phase data, alarm thresholds, historical curves, and communication interruption status.
  • Deliver the point list, wiring records, parameter configuration, and acceptance records.

Limitations and exclusions

  • The terminal cannot replace the short-circuit, overload, and grounding protection design of protective devices.
  • Without complete circuit and CT information, precise circuit-level diagnosis cannot be promised.
  • Specific parameters, accuracy, harmonic order, and communication capabilities are subject to the datasheet of the selected model.

Operational value

  • Establish a unified full-electrical-quantity data entry point for the distribution room.
  • Improve the efficiency of detecting three-phase imbalance, harmonics, and load anomalies.
  • Provide traceable data for capacity assessment, energy consumption analysis, and maintenance planning.

Selection guidance

  • Select SFA, ESE, or a combination of both based on circuit importance and monitoring objectives, avoiding a one-size-fits-all application of the same model to all circuits.
  • When harmonic analysis is required, first confirm the specific ESE model, accuracy, sampling conditions, and CT requirements.
  • Select the number of ESX units and the uplink method based on cabinet distribution and point count.

Typical implementation patterns

  • A typical implementation model is to first establish full-electrical-quantity monitoring on the main incoming line and key feeders, then extend to other circuits by cabinet, with unified access through the gateway. This model does not represent a specific customer project or its operating results.

Before retrofit → With the solution

Before retrofit

  • Voltage, current, power, energy and state data of different cabinets and circuits are scattered and cannot be viewed in a unified way.
  • Three-phase imbalance, harmonics and load changes lack continuous trends, and troubleshooting relies on on-site measurement.

With the solution

  • Establish a unified full-electrical-quantity data entry point for the distribution room.
  • Improve the efficiency of detecting three-phase imbalance, harmonics, and load anomalies.
  • Provide traceable data for capacity assessment, energy consumption analysis, and maintenance planning.

How to evaluate the effect

01

Measurable signal

SFA and ESE acquire circuit electrical parameters in the cabinet;the integration method…

02

Data source

SFA Multi-Parameter Electrical Controller · ESE Power Quality Monitor (Harmonics & THD)

03

Review method

Verify the circuit list, device model, CT ratio and installation location.

04

Acceptance boundary

The terminal cannot replace the short-circuit, overload, and grounding protection design of protective devices.

Frequently asked questions

Is it mandatory to install terminals on all circuits for low-voltage distribution room monitoring?

Not necessarily. You can start with the main incoming line, bus tie, key feeders, and circuits with frequent anomalies, then expand in batches based on O&M value.

How should SFA and ESE divide their roles?

SFA focuses on multi-parameter circuit measurement and control, while ESE is used for circuits that require explicit power quality capabilities; specific functions are subject to the model.

Is ESE still required when there is no harmonic demand?

Not necessarily. If only voltage, current, power, energy, and basic status are needed, evaluation can be based on the SFA model or other configurations.

What is the most important condition before retrofitting existing cabinets?

First confirm the cabinet interior space, CT conditions, outage window, wiring method, and existing communication paths, then determine the terminals and construction batches.

Can the platform directly provide the fault cause?

The platform can provide data and alarm clues, but cannot replace protection action analysis, on-site inspection, or professional personnel judgment.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK