Home / Solutions / Busbar Temperature and Joint Temperature-Rise Monitoring

Busbar Temperature and Joint Temperature-Rise Monitoring

Busbar temperature and joint temperature-rise monitoring should be based on EST temperature products and confirmed sensors; SFA provides electrical parameters of the same circuit for load correlation; ESX aggregates and connects to the platform. The solution must select contact or wireless temperature measurement based on busbar voltage level, insulation distance, installation location, and shielding conditions. ESC is a residual current measurement and control device and cannot be used as a busbar temperature module; the EST temperature range, number of channels, and probe type must also be confirmed by the specific model.

Electrical HazardsTemperature TrendsBusbar Temperature Rise

Solution overview

The solution focuses on continuous temperature trends of heat-generating parts such as busbars, copper busbars, contacts, and cable joints, and uses current or load data to assist in judging whether temperature rise is related to operating conditions.

Applicable industries

  • Industrial and Commercial Power Distribution

Primary user roles

  • Electrical Operations and Maintenance
  • Safety Management Personnel
  • Design Institute

Problems addressed

  • Abnormal temperature rise of busbars, copper busbars, and contacts lacks continuous records, with blind spots between periodic infrared temperature measurements.
  • Temperature measurement points are scattered and may be limited by in-cabinet shielding, insulation distance, and installation conditions.

Recommended product combination

System architecture and data flow

Busbar Temperature and Joint Temperature-Rise Monitoring System TopologyFour-layer data flow across perception, edge control, platform and application for Busbar Temperature and Joint Temperature-Rise Monitoring.01Perception layer
EST temperature terminals and confirmed probes or wireless measurement points collect busbar joint and in-ca…
02Edge / control layer
ESX aggregates temperature and electrical-parameter data, establishing correlations by measurement point and…
03Platform layer
FEXLINK displays temperature curves, load correlation, alarms, and handling records.
04Application layer
O&M personnel arrange inspection, tightening, or infrared re-check based on temperature rise trends.

Perception layer

EST temperature terminals and confirmed probes or wireless measurement points collect busbar joint and in-cabinet temperature.

Edge / control layer

ESX aggregates temperature and electrical-parameter data, establishing correlations by measurement point and circuit.

Platform layer

FEXLINK displays temperature curves, load correlation, alarms, and handling records.

Application layer

O&M personnel arrange inspection, tightening, or infrared re-check based on temperature rise trends.

Data flow

  1. Temperature sensors collect data at busbar or joint measurement points.
  2. EST sends temperature data to ESX.
  3. SFA synchronously provides current or load data of the corresponding circuit.
  4. The platform forms trends and alarms by measurement point and circuit.

Integration and interfaces

  • The measurement point location, probe fixing method, cable routing, and in-cabinet insulation distance must be confirmed.
  • When wireless temperature measurement is used, the frequency band, power supply, shielding, and device density must be verified.
  • Platform points must be consistent with busbar segments, cabinet numbers, and circuit codes.

Applicable standards

  • GB 50054, the GB/T 16895 series, and applicable project-specific temperature-rise requirements for low-voltage switchgear assemblies; the final version is to be confirmed by the project.

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Verify the correspondence of each temperature measurement point with the busbar, joint, or in-cabinet equipment.
  • Verify temperature display, alarm thresholds, communication interruption, and recovery records.
  • Perform integration testing and verification of temperature changes against corresponding circuit loads.
  • Deliver the measurement-point list, installation records, device configuration, and acceptance records.

Limitations and exclusions

  • ESC is not a temperature measurement and control device and must not be used in busbar temperature measurement solutions.
  • Temperature monitoring cannot replace infrared inspection, outage maintenance, or electrical-contact torque checks.
  • Temperature range, accuracy, wireless range, and protection capability must be confirmed by the specific model.

Operational value

  • Supplement periodic manual temperature measurement with continuous trend monitoring.
  • Help identify the engineering correlation between temperature rise and load changes.
  • Provide a data basis for joint inspection, tightening, and maintenance scheduling.

Selection guidance

  • First select wired or wireless temperature measurement based on installation location and insulation distance.
  • Select the EST model based on the number of measurement points, channels, probe type, and on-site shielding conditions.
  • When load correlation is required, configure an available electrical-parameter terminal for the same circuit.

Typical implementation patterns

  • A typical implementation model is to arrange temperature measurement points at busbar segments, key joints, and in-cabinet contacts, and correlate the same circuit's current to platform trends. This description does not represent a specific customer site's exact points or operating results.

Before retrofit → With the solution

Before retrofit

  • Abnormal temperature rise of busbars, copper busbars, and contacts lacks continuous records, with blind spots between periodic infrared temperature measurements.
  • Temperature measurement points are scattered and may be limited by in-cabinet shielding, insulation distance, and installation conditions.

With the solution

  • Supplement periodic manual temperature measurement with continuous trend monitoring.
  • Help identify the engineering correlation between temperature rise and load changes.
  • Provide a data basis for joint inspection, tightening, and maintenance scheduling.

How to evaluate the effect

01

Measurable signal

EST temperature terminals and confirmed probes or wireless measurement points collect bu…

02

Data source

EST Multi-Channel Temperature Monitoring Module · SFA Multi-Parameter Electrical Controller

03

Review method

Verify the correspondence of each temperature measurement point with the busbar, joint, or in-cabinet equipment.

04

Acceptance boundary

ESC is not a temperature measurement and control device and must not be used in busbar temperature measurement solutions.

Frequently asked questions

Can ESC be used for busbar temperature measurement?

No. The confirmed positioning of ESC is as a residual current measurement and control device, not a temperature module.

Is wireless temperature measurement necessarily more convenient than wired?

Not necessarily. Wireless reduces some wiring, but is affected by power supply, shielding, interference, and installation space, so on-site evaluation is required.

Does a temperature rise indicate a contact fault?

It cannot be directly determined. Current, load, ambient temperature, and duration should be considered, and then a professional should inspect the contact status.

Can the same set of products be used for busbars and cable joints?

They can be managed in zones on the same platform, but the measurement point structure, probes, and installation method must be selected separately by object.

Can the circuit be automatically cut off after a platform alarm?

This solution does not include automatic cutoff by default. Whether interlocking is permitted must be designed separately with a control circuit, permissions, and a failure strategy.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK