Home / Solutions / Residual Current and Electrical Fire Monitoring

Residual Current and Electrical Fire Monitoring

Residual current and electrical fire monitoring applies to distribution circuits that require continuous observation of residual current and temperature anomalies. ESF can collect residual current and NTC temperature; ESC is used for multi-circuit residual current monitoring; EST is used for designated temperature measurement points; ESX aggregates and connects to the platform. The solution should clarify the neutral line, protective earth, number of circuit poles, and sensor installation method; the temperature range, residual current range, and relevant certifications must be confirmed by the specific model, and product capability descriptions cannot replace compliance judgments for fire protection or electrical design.

Electrical HazardsResidual Current

Solution overview

The solution is centered on continuous monitoring of leakage current and temperature, helping O&M detect change trends and form alarm records, and applies to distribution cabinets, terminal circuits, and key power-consuming areas.

Applicable industries

  • Industrial and Commercial Power Distribution

Primary user roles

  • Electrical Operations and Maintenance
  • Safety Management Personnel
  • Design Institute

Problems addressed

  • Residual current changes are hidden, making it difficult for periodic inspection to continuously detect insulation degradation or abnormal leakage.
  • Temperature, leakage current, and circuit status are scattered, making it difficult to quickly locate the specific circuit after an alarm.

Recommended product combination

System architecture and data flow

Residual Current and Electrical Fire Monitoring System TopologyFour-layer data flow across perception, edge control, platform and application for Residual Current and Electrical Fire Monitoring.01Perception layer
ESF, ESC, and EST collect residual current and temperature by circuit and measurement point.
02Edge / control layer
ESX aggregates and executes threshold, grading, and alarm rules.
03Platform layer
FEXLINK displays status and trends by distribution cabinet, circuit, and area.
04Application layer
O&M personnel locate the circuit based on the alarm and handle it in combination with on-site inspection and…

Perception layer

ESF, ESC, and EST collect residual current and temperature by circuit and measurement point.

Edge / control layer

ESX aggregates and executes threshold, grading, and alarm rules.

Platform layer

FEXLINK displays status and trends by distribution cabinet, circuit, and area.

Application layer

O&M personnel locate the circuit based on the alarm and handle it in combination with on-site inspection and maintenance processes.

Data flow

  1. Residual current sensors and temperature probes collect on-site data.
  2. ESF, ESC, or EST completes terminal collection.
  3. ESX aggregates and uploads according to circuit relationships.
  4. The platform forms alarms, trends, and handling records.

Integration and interfaces

  • The neutral line, protective earth, number of circuit poles, and residual current sensor installation method must be confirmed.
  • The power supply, channels, probes, and communication parameters of ESF, ESC, and EST must be verified.
  • When connecting to an existing fire protection or monitoring system, it should be clarified whether the alarm is a data prompt or requires contact interlocking.

Applicable standards

  • Applicable clauses related to residual current and temperature monitoring in the GB 14287 series, as well as local fire protection and electrical regulations at the project site; the final version, certificates, and acceptance requirements are to be confirmed by the project.

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Verify residual current and temperature measurement points against platform points circuit by circuit.
  • Verify thresholds, alarms, and recovery behavior through simulation under safe conditions.
  • Check sensor installation, wiring, polarity, power supply, and communication status.
  • Deliver the circuit inventory, point list, configuration records, and acceptance records.

Limitations and exclusions

  • Monitoring alarms cannot replace the protection design of residual current protective devices, circuit breakers, or fire protection systems.
  • The temperature range and residual current range of ESF and EST cannot be interchanged across models.
  • Without accurate neutral line and grounding information, fault point location cannot be promised.

Operational value

  • Bring hidden residual current changes under continuous monitoring.
  • Locate leakage current and temperature anomalies to specific circuits or areas.
  • Form alarm and handling records to support subsequent maintenance.

Selection guidance

  • Select ESF or ESC based on the number of circuits, and supplement EST based on the number of temperature measurement points.
  • When fire protection acceptance is required, first confirm the specific model certification, contact output, and applicable project clauses.
  • Select wired probes or an adapted installation method based on in-cabinet space and wiring conditions.

Typical implementation patterns

  • A typical implementation model is to first deploy residual current and temperature monitoring on key distribution cabinets, then connect floor or terminal circuits in batches by area. This description only represents a common engineering path and does not represent a specific customer site's acceptance conclusion.

Before retrofit → With the solution

Before retrofit

  • Residual current changes are hidden; periodic inspections cannot continuously detect insulation degradation or abnormal leakage
  • Temperature, leakage and circuit status are scattered across different systems; after alarms, quick localization to specific circuits is difficult
  • End circuits and key areas lack continuous temperature records; temperature rise trends are not traceable

With the solution

  • ESF collects residual current and NTC temperature; ESC is used for multi-circuit residual current monitoring; EST is used for independent temperature measurement points
  • ESX aggregates data and executes threshold, grading and alarm rules
  • FEXLINK displays status and trends by distribution cabinet, circuit and area

How to evaluate the effect

01

Measurable signal

Circuit Residual Current Trend

02

Data source

ESF/ESC residual current sensors, continuously collected per circuit

03

Review method

Comparing circuit initial baseline with subsequent value change trends to identify sustained increases or sudden changes

04

Acceptance boundary

Monitoring alarms cannot replace the protection design of residual current protective devices, circuit breakers or fire protection systems

Confirmed per circuit polarity and sensor range; sampling cycle per ESX configuration

Frequently asked questions

Can residual current monitoring replace a leakage current protective device?

No. Monitoring is for data collection and alarming; protection actions still need to be completed by protective devices that meet design requirements.

What is the difference between ESF and ESC?

ESF includes residual current and temperature monitoring capabilities; ESC is a multi-channel residual current measurement and control device; specific channels and ranges are to be confirmed by model.

Is temperature anomaly necessarily caused by leakage current?

Not necessarily. Temperature rise may come from poor contact, overload, ambient temperature, or heat dissipation issues, and requires judgment combined with current and on-site inspection.

Can the same sensor be used for single-phase and three-phase circuits?

Selection must be based on the number of circuit poles, cable structure, and specific sensor specifications, not judged solely by rated current.

Does the platform automatically cut off power after an alarm?

The solution does not include automatic power cutoff by default. Interlocking must be designed separately, with clear relay, permission, reset, and safety responsibilities.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK