Home / Solutions / Lightning Protection and Grounding Monitoring for PV and Energy-Storage Plants

Lightning Protection and Grounding Monitoring for PV and Energy-Storage Plants

Lightning protection and grounding monitoring for PV and energy-storage plants should distinguish DC-side protection, inverter or energy-storage device interfaces, the grounding system and communication routing, combining FS, FSS, FL, FR and optional FG or platform. Third-party device protocols, DC-side boundaries and outdoor installation conditions must be confirmed item by item; AC-side state must not be used to infer DC-side safety state.

Lightning Protection & GroundingGrounding MonitoringLightning Protection Monitoring

Solution overview

This solution addresses scattered plant devices and complex AC/DC boundaries, first establishing a device and grounding-point inventory, then forming a zoned view through the gateway. Internal diagnosis of energy storage and inverters is not replaced by this solution.

Applicable industries

  • PV and Energy Storage

Primary user roles

  • Lightning Protection Engineer
  • Electrical Operations and Maintenance
  • Project Integrator

Problems addressed

  • PV and energy-storage plant devices are scattered, making SPD, lightning current and grounding states difficult to form unified records.
  • The diagnostic boundaries of the DC side, AC side and third-party devices differ, so data cannot be simply merged and interpreted.

Recommended product combination

FS

FS SPD Monitoring Module

Used to collect telemetry signals, circuit breaker, grounding or lightning strike count states from existing SPDs; specific capabilities, power supply and communication suffixes are to be confirmed by the FS model.

FR

FR Grounding Resistance Monitoring Module

As a grounding monitoring product family, select the applicable model by the three-electrode method, the loop method or specific on-site grounding-grid conditions.

System architecture and data flow

Lightning Protection and Grounding Monitoring for PV and Energy-Storage Plants System TopologyFour-layer data flow across perception, edge control, platform and application for Lightning Protection and Grounding Monitoring for PV and Energy-Storage Plants.01Perception layer
Configure FS, FSS, FL or FR at applicable AC power distribution, SPD, down conductor and grounding locations…
02Edge / control layer
Set FG by array, inverter area or energy-storage unit, and adapt to the plant network.
03Platform layer
The platform displays states and events by area, device type and grounding point.
04Application layer
Plant O&M verifies alarms by device zone, jointly with the self-diagnosis of inverters and energy-storage de…

Perception layer

Configure FS, FSS, FL or FR at applicable AC power distribution, SPD, down conductor and grounding locations.

Edge / control layer

Set FG by array, inverter area or energy-storage unit, and adapt to the plant network.

Platform layer

The platform displays states and events by area, device type and grounding point.

Application layer

Plant O&M verifies alarms by device zone, jointly with the self-diagnosis of inverters and energy-storage devices.

Data flow

  1. A plant SPD, lightning or grounding monitoring point changes.
  2. On-site monitoring devices acquire applicable data.
  3. FG aggregates by zone and uploads to the platform.
  4. The platform forms alarms, history and O&M records.

Integration and interfaces

  • Clarify the respective data interfaces of the AC side, DC side and third-party devices.
  • Confirm outdoor protection, device power supply and communication routing conditions.
  • Before integrating with plant monitoring or EMS, complete protocol, point list and security boundary confirmation.

Applicable standards

  • GB/T standards related to lightning protection and grounding of photovoltaic power systems (final version and applicable clauses to be confirmed by the project)
  • GB 50057 Design Code for Lightning Protection of Buildings (applicable clauses to be confirmed by the plant design documents)

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Monitoring points can correspond to an array, inverter area, energy-storage unit or grounding point.
  • AC-side and DC-side data maintain clear boundaries in the platform.
  • Outdoor installation and communication states have traceable records.

Limitations and exclusions

  • This solution cannot replace the internal diagnosis of inverters, energy-storage BMS or DC-side dedicated protection systems.
  • Without confirmed DC-side isolation and work conditions, live integration must not be carried out.
  • Devices in different areas cannot be compared laterally based solely on platform aggregation results.

Operational value

  • Unifies plant lightning-protection and grounding state records.
  • Helps O&M distinguish AC power distribution, lightning events and grounding anomalies.
  • Provides a priority order for zoned plant inspection.

Selection guidance

  • Select FSS or FS according to new or existing AC circuits.
  • Select applicable FL and FR models according to down conductors and grounding-grid structure.
  • When the DC side requires arc, insulation or string diagnosis, conduct a separate product and interface special verification.

Typical implementation patterns

  • A typical implementation pattern is to first pilot in one inverter area and one grounding system, then expand to the energy-storage area.
  • Another pattern integrates AC power distribution, down conductors and grounding points separately, finally forming a plant view.

Before retrofit → With the solution

Before retrofit

  • PV and energy-storage plant devices are scattered, making SPD, lightning current and grounding states difficult to form unified records.
  • The diagnostic boundaries of the DC side, AC side and third-party devices differ, so data cannot be simply merged and interpreted.

With the solution

  • Unifies plant lightning-protection and grounding state records.
  • Helps O&M distinguish AC power distribution, lightning events and grounding anomalies.
  • Provides a priority order for zoned plant inspection.

How to evaluate the effect

01

Measurable signal

Configure FS, FSS, FL or FR at applicable AC power distribution, SPD, down conductor and…

02

Data source

FS SPD Monitoring Module · FSS Smart Surge Protective Device (Flagship)

03

Review method

Monitoring points can correspond to an array, inverter area, energy-storage unit or grounding point.

04

Acceptance boundary

This solution cannot replace the internal diagnosis of inverters, energy-storage BMS or DC-side dedicated protection systems.

Frequently asked questions

Can PV DC-side arcs be monitored?

This combination does not default to DC arc monitoring capability; a corresponding dedicated product and interface must be selected and verified separately.

Will energy-storage BMS alarms enter the same platform?

They can be integrated by project, but the original states and responsibility boundaries of third-party devices should be retained.

Can all outdoor devices be installed directly?

Cannot be assumed by default. Protection, temperature, power supply and installation method must be confirmed by the specific model and environment.

What devices does "lightning protection and grounding monitoring for PV and energy-storage plants" typically consist of?

FS: collects telemetry signals, circuit breaker, grounding or lightning strike count states from existing SPDs; specific capabilities, power supply and communication suffixes are confirmed by the FS model; FSS: as an integrated smart SPD combining protection and condition monitoring, selected by number of poles, protection parameters and circuit conditions; FL: records events such as lightning current peak and energy; indoor/outdoor model, range, protection rating and installation orientation are confirmed by the datasheet; FR: as a grounding monitoring product family, select the applicable model by the three-electrode method, the loop method or specific on-site grounding-grid conditions.

What site conditions should be verified before implementing "lightning protection and grounding monitoring for PV and energy-storage plants"?

Select FSS or FS according to new or existing AC circuits; select applicable FL and FR models according to down conductors and grounding-grid structure; when the DC side requires arc, insulation or string diagnosis, conduct a separate product and interface special verification.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK