Home / Solutions / Online Grounding Resistance Monitoring for Substations and Distribution Stations

Online Grounding Resistance Monitoring for Substations and Distribution Stations

Online grounding resistance monitoring for substations and distribution stations should first confirm the grounding-grid structure, down conductors and auxiliary electrode conditions, then adopt an applicable FR-01311 or FRP scheme. The three-electrode method and the loop method cannot be interchanged by product name; platform values should be interpreted in combination with the on-site test method and environmental conditions, and the overall grounding-grid state must not be judged from a single reading alone.

Lightning Protection & GroundingGrounding Monitoring

Solution overview

This solution reduces blind spots in manual grounding testing and establishes traceable monitoring records. FR-01311 applies to three-electrode-method scenarios with auxiliary-electrode conditions; when such conditions are unavailable, re-evaluate the FRP loop method or other monitoring methods.

Applicable industries

  • Substations and Distribution Stations

Primary user roles

  • Lightning Protection Engineer
  • Electrical Operations and Maintenance
  • Project Integrator

Problems addressed

  • Manual grounding resistance testing has a long cycle, making grounding-grid corrosion, disconnection or connection changes difficult to observe continuously.
  • Site grounding-grid structures and auxiliary-electrode conditions vary widely, so one measurement principle cannot be applied directly to all stations.

Recommended product combination

FEXLINK

FEXLINK IoT Platform

Provides device management, alarm, historical data, permission and O&M record capabilities; the deployment method is to be confirmed by the project.

FRP

FRP Loop-Method Grounding Resistance Monitor

Used for loop-method grounding resistance or grounding continuity monitoring; installation method, range, protection and explosion-proof conditions are verified by the specific model.

System architecture and data flow

Online Grounding Resistance Monitoring for Substations and Distribution Stations System TopologyFour-layer data flow across perception, edge control, platform and application for Online Grounding Resistance Monitoring for Substations and Distribution Stations.01Perception layer
Configure FR-01311 three-electrode-method monitoring or a confirmed FRP loop-method device according to grou…
02Edge / control layer
FG aggregates grounding monitoring data and retains measurement point, measurement method and time informati…
03Platform layer
FEXLINK forms grounding trends, threshold alarms and inspection records.
04Application layer
O&M personnel verify anomalies in combination with season, soil and on-site test results, and arrange ground…

Perception layer

Configure FR-01311 three-electrode-method monitoring or a confirmed FRP loop-method device according to grounding-grid conditions.

Edge / control layer

FG aggregates grounding monitoring data and retains measurement point, measurement method and time information.

Platform layer

FEXLINK forms grounding trends, threshold alarms and inspection records.

Application layer

O&M personnel verify anomalies in combination with season, soil and on-site test results, and arrange grounding-system maintenance.

Data flow

  1. The on-site grounding device and auxiliary electrode form the measurement conditions.
  2. FR-01311 or an applicable FRP model acquires the grounding monitoring data.
  3. FG aggregates the measurement points and uploads them to the platform.
  4. The platform displays trends, alarms and manual verification records.

Integration and interfaces

  • Confirm down conductors, auxiliary electrodes, grounding test points and wiring paths.
  • Specify the specific model and datasheet corresponding to the monitoring principle, range and accuracy.
  • When integrating with existing power monitoring, retain the measurement method, units and quality identifiers.

Applicable standards

  • GB 50057 Design Code for Lightning Protection of Buildings (applicable clauses and version to be confirmed by the project location and design documents)
  • GB/T 21431 Technical Code for Inspection of Lightning Protection Devices (final version and test method to be confirmed by the project)

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Each grounding measurement point has a unique number, its belonging grounding grid and a measurement-method description.
  • The platform can distinguish normal, out-of-limit, device offline and communication interruption.
  • Anomaly records can be associated with on-site verification results and retain the handling time.

Limitations and exclusions

  • Online monitoring records cannot replace on-site grounding testing required by law or by the project.
  • A single measurement-point reading does not automatically represent the state of the entire grounding grid.
  • Changes in soil, season and construction conditions affect interpretation and must be combined with on-site verification.

Operational value

  • Supplements continuous observation capability between manual tests.
  • Provides a trend basis for grounding-grid corrosion, connection changes and maintenance prioritization.
  • Unifies grounding monitoring records across scattered stations.

Selection guidance

  • When auxiliary-electrode and construction conditions are available, the FR-01311 three-electrode-method scheme can be evaluated.
  • When auxiliary-electrode conditions are unavailable, evaluate the FRP loop method rather than force-reusing the three-electrode-method product.
  • Range, accuracy, protection and environmental conditions are confirmed by the specific model and on-site datasheet.

Typical implementation patterns

  • A typical implementation pattern is to first pilot representative grounding points, then expand measurement points by grounding-grid zone.
  • Another pattern is to keep online trends side by side with existing periodic test records for easy verification.

Before retrofit → With the solution

Before retrofit

  • Manual grounding resistance testing has a long cycle, making grounding-grid corrosion, disconnection or connection changes difficult to observe continuously.
  • Site grounding-grid structures and auxiliary-electrode conditions vary widely, so one measurement principle cannot be applied directly to all stations.

With the solution

  • Supplements continuous observation capability between manual tests.
  • Provides a trend basis for grounding-grid corrosion, connection changes and maintenance prioritization.
  • Unifies grounding monitoring records across scattered stations.

How to evaluate the effect

01

Measurable signal

Configure FR-01311 three-electrode-method monitoring or a confirmed FRP loop-method devi…

02

Data source

FR-01311 Grounding Resistance Online Tester (Three-Electrode Method) · FG Smart Gateway (Zigbee, RS485 & Ethernet)

03

Review method

Each grounding measurement point has a unique number, its belonging grounding grid and a measurement-method description.

04

Acceptance boundary

Online monitoring records cannot replace on-site grounding testing required by law or by the project.

Frequently asked questions

Can the three-electrode method and the loop method be swapped at will?

No. The two have different measurement principles and site conditions, and must be selected according to the grounding-grid structure, auxiliary electrodes and installation method.

Can online monitoring replace manual testing?

Not directly. Online data is for continuous observation; testing required by law or by the project must still be performed as specified.

Why can readings from different stations not be compared directly across the board?

Soil, season, grounding-grid structure and measurement method may differ; they should be interpreted in combination with point conditions and on-site test results.

What devices does "online grounding resistance monitoring for substations and distribution stations" typically consist of?

FR-01311: uses the three-electrode method for online grounding resistance monitoring, requiring grounding-grid structure and auxiliary-electrode installation conditions; FG: aggregates downstream lightning-protection monitoring devices, performs protocol conversion and transmits states and events to the upper-level platform; FEXLINK: provides device management, alarm, historical data, permission and O&M record capabilities, with the deployment method confirmed by the project; FRP: used for loop-method grounding resistance or grounding continuity monitoring, with installation method, range, protection and explosion-proof conditions verified by the specific model.

What site conditions should be verified before implementing "online grounding resistance monitoring for substations and distribution stations"?

When auxiliary-electrode and construction conditions are available, the FR-01311 three-electrode-method scheme can be evaluated; when auxiliary-electrode conditions are unavailable, evaluate the FRP loop method rather than force-reusing the three-electrode-method product; range, accuracy, protection and environmental conditions are confirmed by the specific model and on-site datasheet.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK