Home / Solutions / Lightning Protection and Grounding for Petrochemical Plants and Tank Farms

Lightning Protection and Grounding for Petrochemical Plants and Tank Farms

Lightning protection and grounding for petrochemical plants and tank farms should be designed point by point in combination with hazardous areas, corrosive environments, grounding grids and SPD circuits; when combining FS, FSS, FL and FR, the basis must be specific models, certificates and project standards. Monitoring can be used to discover state changes and events, but a safety conclusion must not be drawn separately from the corrosion, explosion-proof, interlock and on-site testing systems.

Lightning Protection & GroundingGrounding MonitoringLightning Protection Monitoring

Solution overview

This solution targets complex scenarios where corrosion, disconnection, static discharge and lightning risk are coupled. First perform risk and area division, then determine monitoring points and product configuration.

Applicable industries

  • Petrochemical and Hazardous-Goods Storage

Primary user roles

  • Explosion-Proof Electrical Engineer
  • Safety Management Personnel
  • Instrumentation O&M

Problems addressed

  • Corrosion and connection changes make grounding hazards difficult to discover through periodic inspection alone.
  • Hazardous areas, maintenance windows and interlock boundaries are strict, limiting monitoring devices and construction methods.

Recommended product combination

FS

FS SPD Monitoring Module

Used to collect telemetry signals, circuit breaker, grounding or lightning strike count states from existing SPDs; specific capabilities, power supply and communication suffixes are to be confirmed by the FS model.

FR

FR Grounding Resistance Monitoring Module

As a grounding monitoring product family, select the applicable model by the three-electrode method, the loop method or specific on-site grounding-grid conditions.

System architecture and data flow

Lightning Protection and Grounding for Petrochemical Plants and Tank Farms System TopologyFour-layer data flow across perception, edge control, platform and application for Lightning Protection and Grounding for Petrochemical Plants and Tank Farms.01Perception layer
Configure applicable products at approved grounding points, SPDs and down-conductor paths;device capabilitie…
02Edge / control layer
Set aggregation gateways in safe areas or justified locations to complete data isolation and upload.
03Platform layer
The platform establishes alarm and historical records by plant unit, tank farm and monitoring object.
04Application layer
Electrical, safety and O&M personnel verify according to the hazardous-area management process;monitoring re…

Perception layer

Configure applicable products at approved grounding points, SPDs and down-conductor paths; device capabilities are confirmed by model and certificate.

Edge / control layer

Set aggregation gateways in safe areas or justified locations to complete data isolation and upload.

Platform layer

The platform establishes alarm and historical records by plant unit, tank farm and monitoring object.

Application layer

Electrical, safety and O&M personnel verify according to the hazardous-area management process; monitoring results do not directly trigger unapproved actions.

Data flow

  1. An on-site grounding, SPD or lightning state changes.
  2. Applicable monitoring devices acquire the corresponding information.
  3. The aggregation gateway completes data processing at a permitted location.
  4. The platform forms alarms and maintenance clues.

Integration and interfaces

  • Confirm hazardous areas, device certificates, power supply and communication paths.
  • Confirm the boundaries of existing safety instruments, process and electrical systems.
  • Conduct special approval for interfaces, data permissions and alarm-response responsibilities.

Applicable standards

  • GB 50058 Design Code for Electrical Installations in Explosive Hazardous Atmospheres (final version and hazardous-area conditions to be confirmed by the project)
  • GB/T 21431 Technical Code for Inspection of Lightning Protection Devices (test items to be confirmed by the project)

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Each point has records of plant unit, area, device model and installation method.
  • Monitoring alarms have clear boundaries from existing SIS, DCS or electrical systems.
  • On-site verification, maintenance and recovery records are complete.

Limitations and exclusions

  • Monitoring data alone cannot serve as a conclusion on the plant's safety state.
  • Without confirmed certificates and installation process, construction in hazardous areas must not proceed.
  • This solution does not replace SIS, fire protection, anti-static or statutory testing.

Operational value

  • Provides trend records for grounding-state changes in corrosive environments.
  • Supports arranging maintenance by plant unit and area.
  • Forms an O&M basis for lightning and SPD events.

Selection guidance

  • First complete hazardous-area and grounding-system design review.
  • Verify protection, corrosion, explosion-proof and certification information by accurate model.
  • Select FS, FSS, FL or FR according to down conductors, grounding grid and SPD conditions.

Typical implementation patterns

  • A typical candidate pattern is to first verify the device and data link in a non-critical area.
  • Another pattern integrates by plant-unit zone and manages in parallel with existing electrical and safety records.

Before retrofit → With the solution

Before retrofit

  • Corrosion and connection changes make grounding hazards difficult to discover through periodic inspection alone.
  • Hazardous areas, maintenance windows and interlock boundaries are strict, limiting monitoring devices and construction methods.

With the solution

  • Provides trend records for grounding-state changes in corrosive environments.
  • Supports arranging maintenance by plant unit and area.
  • Forms an O&M basis for lightning and SPD events.

How to evaluate the effect

01

Measurable signal

Configure applicable products at approved grounding points, SPDs and down-conductor path…

02

Data source

FS SPD Monitoring Module · FSS Smart Surge Protective Device (Flagship)

03

Review method

Each point has records of plant unit, area, device model and installation method.

04

Acceptance boundary

Monitoring data alone cannot serve as a conclusion on the plant's safety state.

Frequently asked questions

Why not give a specific explosion-proof rating directly?

Explosion-proof capability must be bound to the accurate model, certificate and installation conditions; it cannot be written into the page before verification.

Can it be integrated with DCS?

It can be justified by the project interface, but the separation of monitoring and process-control responsibilities should be maintained.

How is maintainability improved in corrosive environments?

Corrosion protection, accessibility and maintenance methods should be confirmed during selection and installation, rather than relying only on platform alarms.

What devices does "lightning protection and grounding for petrochemical plants and tank farms" typically consist of?

FS: collects telemetry signals, circuit breaker, grounding or lightning strike count states from existing SPDs; specific capabilities, power supply and communication suffixes are confirmed by the FS model; FSS: as an integrated smart SPD combining protection and condition monitoring, selected by number of poles, protection parameters and circuit conditions; FL: records events such as lightning current peak and energy; indoor/outdoor model, range, protection rating and installation orientation are confirmed by the datasheet; FR: as a grounding monitoring product family, select the applicable model by the three-electrode method, the loop method or specific on-site grounding-grid conditions.

What site conditions should be verified before implementing "lightning protection and grounding for petrochemical plants and tank farms"?

First complete hazardous-area and grounding-system design review; verify protection, corrosion, explosion-proof and certification information by accurate model; select FS, FSS, FL or FR according to down conductors, grounding grid and SPD conditions.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK