Home / Solutions / Itemized Metering for Mixed Single-Phase and Three-Phase Circuits in Distribution Cabinets

Itemized Metering for Mixed Single-Phase and Three-Phase Circuits in Distribution Cabinets

Itemized metering for mixed single-phase and three-phase circuits should first divide boundaries by ownership, area or energy responsibility, then select meters and connection methods that match single-phase and three-phase circuits. Direct connection versus CT connection depends on rated current, cabinet space and installation conditions; data enters the platform after protocol unification through the gateway. Accuracy class, circuit count and tariff capability must be confirmed against the specific model, the CTs and project acceptance requirements.

Energy DataSub-MeteringMetering Acquisition

Solution overview

The solution addresses inconsistent metering units, confused multipliers and inconsistent protocols when one distribution cabinet contains single-phase lighting, socket, control supply and three-phase power circuits. The core work is to establish the circuit register, meter type, connection method, communication address and platform sub-metering model clearly in one pass.

Applicable industries

  • Industrial parks
  • Commercial buildings
  • Manufacturing plants

Primary user roles

  • Energy managers
  • Electrical design
  • Metering O&M

Problems addressed

  • A cabinet contains both single-phase and three-phase circuits, with inconsistent metering boundaries, connection methods and protocols
  • Circuit names, purposes and meter addresses lack a correspondence, which makes later allocation and location difficult
  • Mixed direct and CT connections easily lead to multiplier and data definition errors

Recommended product combination

DDSU1589

DDSU1589 Single-Phase Electronic Energy Meter

Used for active, reactive and energy metering on single-phase circuits; communication, tariff and prepayment-related capabilities are confirmed against the specific model range

CW

CW Edge Computing Gateway

Connects different meters, performs address management, protocol conversion, buffering and platform upload

FEXLINK

FEXLINK IoT Platform

Maintains the hierarchy of cabinets, circuits, energy areas and meters, and generates sub-metering statistics, comparisons and exportable reports

System architecture and data flow

Itemized Metering for Mixed Single-Phase and Three-Phase Circuits in Distribution Cabinets System TopologyFour-layer data flow across perception, edge control, platform and application for Itemized Metering for Mixed Single-Phase and Three-Phase Circuits in Distribution Cabinets.01Perception layer
Single-phase circuits use matching single-phase meters;three-phase circuits use three-phase meters according…
02Edge / control layer
CW acquires meters over an RS485 bus or a project-confirmed interface, unifying device addresses, communicat…
03Platform layer
FEXLINK builds the register of cabinets, circuits, energy units and metering multipliers and produces sub-me…
04Application layer
Shows area and purpose sub-metering to energy managers, and meter status, communication status and multiplie…

Perception layer

Single-phase circuits use matching single-phase meters; three-phase circuits use three-phase meters according to current and installation conditions; high-current circuits use confirmed CT connection with the ratio recorded

Edge / control layer

CW acquires meters over an RS485 bus or a project-confirmed interface, unifying device addresses, communication parameters and the upload model

Platform layer

FEXLINK builds the register of cabinets, circuits, energy units and metering multipliers and produces sub-metering summaries and anomaly checks

Application layer

Shows area and purpose sub-metering to energy managers, and meter status, communication status and multiplier information to metering O&M staff

Data flow

  1. The circuit register defines cabinet number, circuit number, purpose, supply system, rated current and metering method
  2. Single-phase and three-phase meters connect to the gateway with confirmed communication parameters; CT circuits also register the ratio
  3. The gateway performs acquisition, time stamping, buffering and protocol conversion before uploading to the platform
  4. The platform calculates energy using meter multipliers and sub-metering boundaries and generates daily, monthly or custom-period reports
  5. Communication loss, multiplier anomalies or data gaps enter the O&M verification process

Integration and interfaces

  • DDSU1589 can use a project-confirmed RS485 interface with DL/T 645 or Modbus-RTU; the protocol version is checked against the device documentation
  • ZSA-31331 uses a project-confirmed RS485 and Modbus-RTU interface; register tables and data types are checked before connection
  • When the gateway provides data to the platform or a customer system, it uses a project-confirmed MQTT, HTTP API or local interface
  • CT ratio, polarity, conductor direction and secondary wiring must be recorded in the point list and used in the calculation

Applicable standards

  • Applicable project standards for electrical metering, LV distribution and sub-metered consumption statistics; the final edition is confirmed against project location, industry and project documents
  • Meter communication can use project-confirmed protocols such as DL/T 645 or Modbus-RTU; platform interfaces are defined per project

Acceptance and delivery boundaries

Suggested acceptance dimensions

  • Check cabinet by cabinet that the single-phase and three-phase circuit register, meter addresses, purposes, multipliers and communication parameters correspond
  • Sample-check readings on direct and CT-connected circuits and verify plausibility and error against independent measurement or known loads
  • Verify that daily and monthly reports calculate correctly across midnight, backfill and multiplier changes
  • Check that communication loss, offline meters, data gaps and abnormal multipliers raise clear alarms

Limitations and exclusions

  • One meter cannot represent several circuits whose ownership or responsibility boundaries are unclear
  • Without recorded CT ratio, polarity and secondary wiring, platform readings cannot be used directly for cost allocation
  • A meter display value is not the same as third-party calibrated settlement energy; settlement use requires separate confirmation against local metering requirements
  • Tariff and prepayment capability depend on the specific meter and platform rules and cannot be committed uniformly before the model is confirmed

Operational value

  • Turns cabinets with mixed supply systems into sub-metering units with clear, verifiable boundaries
  • Reduces statistical errors caused by inconsistent circuit naming, CT ratios and protocols
  • Provides a unified data basis for tenant allocation, area analysis and key circuit upgrades

Selection guidance

  • Decide by purpose and ownership which circuits must be metered independently, rather than by the free space left in the cabinet
  • Choose direct or CT connection according to rated current and installation conditions; for high current and retrofit work, check CT mounting space and the shutdown window first
  • Where demand, events or curves are needed, select the corresponding three-phase meter; for sub-metered energy only, a simplified configuration that meets project requirements is sufficient
  • Single-phase and three-phase meters can be mixed, but device naming, multipliers, time zone and data periods should be unified on the platform side

Typical implementation patterns

  • Typical implementation pattern: a park divides circuits in existing cabinets by lighting, power, tenant and common area, configures single-phase or three-phase meters, connects them through a gateway to the platform, and verifies sub-metered results against the cabinet, circuit and multiplier register. This is an anonymized typical pattern and does not represent specific customer settlement results.

Before retrofit → With the solution

Before retrofit

  • A cabinet contains both single-phase and three-phase circuits, with inconsistent metering boundaries, connection methods and protocols
  • Circuit names, purposes and meter addresses lack a correspondence, which makes later allocation and location difficult
  • Mixed direct and CT connections easily lead to multiplier and data definition errors

With the solution

  • Turns cabinets with mixed supply systems into sub-metering units with clear, verifiable boundaries
  • Reduces statistical errors caused by inconsistent circuit naming, CT ratios and protocols
  • Provides a unified data basis for tenant allocation, area analysis and key circuit upgrades

How to evaluate the effect

01

Measurable signal

Single-phase circuits use matching single-phase meters;three-phase circuits use three-ph…

02

Data source

DDSU1589 Single-Phase Electronic Energy Meter · ZSA-31331 Smart Distribution Box (Single/Three-Phase Metering)

03

Review method

Check cabinet by cabinet that the single-phase and three-phase circuit register, meter addresses, purposes, multipliers and communication parameters correspond

04

Acceptance boundary

One meter cannot represent several circuits whose ownership or responsibility boundaries are unclear

Frequently asked questions

Do single-phase and three-phase circuits need different meters?

Meters are usually selected to match the circuit supply system and wiring. Whether one multi-function meter can serve both must follow the wiring diagram, rated voltage and specific model documentation.

When is CT connection used?

When circuit current exceeds the meter's direct-connection capability, or when the existing cabinet already has suitable CTs and installation conditions. Rated current, ratio, load and installation space must be verified.

Where is the CT ratio handled?

The platform or acquisition system must record each CT ratio and its circuit, then convert accordingly. CT polarity, conductor direction and secondary wiring also need checking during commissioning.

Must sub-metering use the same protocol?

The meters themselves do not need identical protocols, but the gateway must support the relevant protocols and form a unified point model on the platform. Protocol versions, registers and data types must be checked before connection.

Can it be used directly for tenant cost allocation?

It can be used for internal energy management first. Formal settlement requires separate confirmation of metering instruments, calibration, tariffs, dispute handling and local regulatory requirements.

Request a matched product combination and project review

Share the application, circuit conditions and existing system interfaces so engineers can confirm selection and implementation boundaries.

Contact FEXLINK