Direct Answer

Should sub-metering meters be settlement-grade or management-grade? Select by use — circuits that settle with the grid or charge externally use settlement-grade meters (Class 0.5S or above, meeting metrological verification requirements), while internal assessment and energy-saving analysis circuits use management-grade meters (Class 1.0 is enough); concentrate the high-accuracy budget on settlement and key assessment points.

A scenario: A factory is selecting meters — buying all high-accuracy meters costs too much, but buying all ordinary meters raises the worry that assessment data will not be recognized — it cannot decide. The logic of the trade-off is to grade by circuit use — settlement-grade for external settlement and management-grade for internal management — spend the high-accuracy budget on settlement and key assessment points.

1. The Legal Difference between Settlement Metering and Management Metering

The position of settlement metering — the external basis: the basis of settlement with the grid and superior units; The position of management metering — the internal tool: the data source of internal assessment and energy-saving analysis; The legal requirement — settlement metering must be legally verified: metering instruments used for trade settlement must pass verification; Management metering — no mandatory verification: internal management meters have no mandatory verification requirement.

In one sentence: settlement metering is the external settlement basis and must be legally verified; management metering is the internal management tool and needs no mandatory verification.

The responsibility boundary of the two types — settlement metering is responsible for the "account": the data affects the electricity bill and cost accounting, leaving little room for error; management metering is responsible for the "trend": the data is used to find problems and guide energy saving, allowing reasonable error.

An example: A factory mixes the two types: the settlement circuit with the grid uses a Class 0.5S meter with verification, and the workshop assessment circuit uses a Class 1.0 meter. The logic is that the legal difference is the watershed of selection — settlement metering involves external interests and regulations require verified instruments — management metering is internal only with no mandatory verification — first distinguish the nature of the circuit, then decide the accuracy class — the legal boundary cannot be blurred.

2. Accuracy Class, Verification Requirements and the Price Gap

The accuracy of settlement grade — Class 0.5S or above: small error, suitable for trade settlement; The accuracy of management grade — Class 1.0: acceptable error, suitable for internal management; The verification requirement — settlement grade needs verification: verified periodically to guarantee accurate metering; The price reality — high-accuracy meters are expensive: a Class 0.5S meter costs noticeably more than a Class 1.0.

In one sentence: the accuracy is Class 0.5S or above with verification for settlement grade and Class 1.0 without verification for management grade — high-accuracy meters carry an obvious price gap.

The composition of the price gap — the gap lies mainly in the metering chip and the verification process: a Class 0.5S meter needs higher-accuracy sampling and factory verification, so the cost naturally rises; Class 1.0 meters have mature processes and large production volumes, so the price is friendlier.

The comparison table of accuracy and use:

Accuracy classApplicable circuitVerification requirementTypical use
Class 0.5S or aboveSettlement, gateway, external chargingLegal verificationTrade settlement, external reporting
Class 1.0Internal assessment, energy-saving analysisNo mandatory verificationWorkshop assessment, trend comparison

An example: A factory compares prices: a Class 0.5S meter is about 40%-60% more expensive than a Class 1.0, a clear difference. The logic is that the price gap is a real trade-off dimension — a Class 0.5S meter on the settlement circuit returns the extra money — a Class 1.0 on the management circuit is enough — accuracy is not the highest the better, but selected by use.

3. Which Circuits Must Use Settlement Grade

Circuit one, settlement with the grid — the gateway circuit: the total incoming line and the gateway metering must be settlement grade; Circuit two, external charging — transfer circuits: circuits charging tenants and independent units must be settlement grade; Circuit three, superior assessment — superior settlement: circuits settling with superior units need settlement grade; Circuit four, key assessment — important nodes: key nodes involving external assessment use settlement grade.

In one sentence: settlement grade covers the gateway circuit, external charging, superior settlement and key assessment — circuits involving external interests must be settlement grade.

The judgment list for circuit classification — ask three questions first: does the electricity of this circuit have to be settled externally? Does the data have to be reported to a superior? Does the assessment result have to be recognized externally? — if any answer is yes, the circuit needs settlement grade.

An example: A factory classifies circuits: the total incoming line uses Class 0.5S, tenant transfer uses Class 0.5S and workshop assessment uses Class 1.0. The logic is that the criterion for settlement grade is whether external interests exist — settling with the grid, charging tenants and reporting to a superior all need settlement grade — pure internal assessment uses management grade — external circuits are few and precise, and the high-accuracy budget is spent on the cutting edge — answer the three questions and circuit grading is no longer a struggle.

4. The Sufficient Boundary of Management-Grade Meters in Energy-Saving Analysis

Boundary one, trend analysis — sufficient: energy-saving analysis looks at trends and comparisons, and Class 1.0 is enough; Boundary two, relative comparison — sufficient: period comparison and cross comparison only need relative accuracy; Boundary three, unit-consumption statistics — sufficient: equipment unit-consumption statistics are met by Class 1.0; Boundary four, external output — not enough: external settlement and charging with Class 1.0 data is not enough.

In one sentence: the sufficient boundary of management grade covers trends, comparisons and unit-consumption statistics; it is not enough for external settlement and charging.

A practical reminder for management grade — management-grade meters also need periodic checking: even without mandatory verification, calibrate them regularly against a reference to prevent long-term drift from harming data quality.

An example: A factory does energy-saving analysis: it uses Class 1.0 meters for workshop unit-consumption comparison — the data is consistent and the conclusion is reliable. The logic is that the essence of energy-saving analysis is comparison — trends, comparisons and unit-consumption statistics are all relative quantities — the error of a Class 1.0 meter does not change the direction of the conclusion — only when the data leaves the internal scope does higher accuracy become necessary — for internal trend watching, Class 1.0 is enough.

5. Cost Allocation Suggestions for Selection

Suggestion one, graded selection — by use: settlement circuits use settlement grade and management circuits use management grade; Suggestion two, budget concentration — spend high accuracy on the cutting edge: concentrate Class 0.5S on settlement and key assessment; Suggestion three, unified platform — consistent data: meters of different classes are uniformly accessed into the supervision center; Suggestion four, phased procurement — settlement first, management later: procure settlement-grade meters in phase one and supplement management grade in phase two.

In one sentence: the cost allocation is graded selection, budget concentration, platform unification and phased procurement.

The cost-comparison reference — versus buying all Class 0.5S meters: the graded scheme uses Class 1.0 on management circuits and can save about 30% of the total investment — the saved budget goes to more points or platform functions.

Back to the YESLON product match — the settlement circuit can use the ESA full-element smart meter (high-accuracy metering) and the management circuit can use the ZSA embedded multi-function smart meter (in-cabinet itemization) — both types are uniformly accessed into the energy supervision center solution with consistent data standards and tiered reports.

An example: A factory procures: phase one buys 4 settlement-grade meters and 20 management-grade meters — the investment saves about 30%. The logic is that the final goal of selection is matching cost with accuracy — graded selection makes every yuan worth spending — platform unification makes data from different classes comparable — phased procurement keeps the investment rhythm controllable — decide the whole procurement once and land it by grade.

Settlement-grade or management-grade? — grade by circuit use: circuits that settle with the grid, charge externally or report to superiors use settlement grade (Class 0.5S or above with legal verification), and internal assessment and energy-saving analysis circuits use management grade (Class 1.0 is enough) — concentrate the high-accuracy budget on settlement and key assessment points — accuracy follows the use, and the cost stays controlled.

Scope and Limitations

  • The conclusions in this article are intended for LV distribution and electrical-safety sites. Standard numbers (DL/T 448, GB/T 17215) refer to their currently effective editions, and product parameters follow the latest FEXLINK selection handbook and product knowledge base.
  • Quantitative criteria (protection zone, discharge and residual voltage, earth resistance, thresholds and grading) hold under the preconditions stated in this article. Where the site voltage level, earthing arrangement, environmental category or load profile differs, the figures must be recalculated. Specific configurations involving ESA all-element smart meter, ZSA embedded multi-function smart meter should be verified against actual circuit parameters.
  • Specific product models and parameters are subject to the latest selection handbook and product knowledge base; this article does not constitute selection or procurement advice.
  • Standard numbers cited here refer to the currently effective editions; when a standard is revised, the related quantitative conclusions must be re-checked.
  • Deployment and implementation for specific projects must be carried out by qualified engineers based on site survey and design drawings.

Frequently Asked Questions

For Sub-Metering

Select by use — circuits that settle with the grid or charge externally use settlement-grade meters (Class 0.5S or above