Direct Answer
The project team wants a sensor on every screw — is more data always a more accurate model? AI models feed on high-quality data that is "labeled, attributed and positioned", not "large in quantity" — redundant sensors introduce noise, dilute alarm association and slow down Qianzhi parallelism; the right approach is precise placement by "four position levels plus key parameters" — fewer but better.
A scenario: A project goes "full acquisition" — 10 sensors on every device — the budget spread thin — after go-live alarm association is chaotic — Qianzhi analysis slows — review finds: key joints not placed well, a large patch of redundant sensors — after replanning, model accuracy rises. The logic of placement is that models feed on quality, not quantity — key points placed well beat full acquisition.
1. Is More Data Always a More Accurate Model
The intuitive misconception — more is better: a large data volume equals accuracy; What AI really needs — quality first: labeled, attributed and positioned; The cost of quantity — noise introduced: redundant data disturbs model learning; The cost of quantity, second — budget waste: sensors, bandwidth and maintenance expenses; The right mindset — precise placement: fewer but better, key points placed well.
In one sentence: models feed on quality, not quantity — place precisely, fewer but better.
An example: A project acquires 3,000 sensors in full — model accuracy drops instead — streamlined to 800 key points — accuracy recovers. The logic is that volume is not the goal — what matters is whether data is labeled, attributed and positioned — redundant data is a burden, not an asset.
2. What AI Models Actually Feed On
Labeled — data with tags: every piece knows what it is and its state; Attributed — data with ownership: every piece links to a specific device; Positioned — data with a location: every piece knows its cabinet and circuit; Noise-free — clean data: interference, duplication and errors removed; Relatable — data that links: different sensors can establish causal relations.
In one sentence: AI feeds on labeled, attributed, positioned, noise-free and relatable data.
An example: A factory's data comparison: redundant sensors without attribution — the model learns nothing; key sensors complete — the model warns accurately. The logic is that data quality sets the model ceiling — without labels and attribution, more data is just more noise.
3. The Three Side Effects of Redundant Sensors
Side effect one, noise introduced — redundant data disturbs: the model learns wrong associations; Side effect two, association diluted — alarm correlation weakens: real alarms are drowned out; Side effect three, parallelism slowed — Qianzhi analysis slows: data volume drags computation; The root of the side effects — no goal: acquiring for the sake of acquiring; The conclusion — redundancy harms: fewer but better, precision first.
In one sentence: the three side effects of redundancy are noise, diluted association and slower parallelism — acquiring for the sake of acquiring.
An example: A project's redundant sensors: 3,000 points fully acquired — alarm association chaotic — Qianzhi slow — streamlined and back to normal. The logic is that redundancy is not an extra layer of safety — it introduces noise, dilutes association and slows computation — three real side effects.
4. Three Principles of Precise Placement
Principle one, key circuits — place on key circuits: main loops, important loads, incoming lines; Principle two, key joints — place on key joints: busbar joints, cable terminations, terminals; Principle three, key parameters — place on key parameters: temperature rise, current, partial discharge, harmonics; The common thread — pointing at risk: placement follows the risk; The essence — precise rather than comprehensive: key points placed well, risks fully covered.
In one sentence: the three principles are key circuits, key joints and key parameters — placement follows the risk.
An example: A project places by the three principles: 20 points on main loops, 30 on busbar joints, key parameters fully covered — all risk points monitored — cost down 40%. The logic is that placement must be precise — wherever the risk is, the sensor goes — key points complete beat area coverage.
5. How to Place Across the Four Position Levels
Level one, device level — the whole device: transformer, motor and cabinet state; Level two, circuit level — circuit monitoring: feeder, load and incoming current; Level three, joint level — contact monitoring: busbar joint and cable termination temperature rise; Level four, parameter level — deep parameters: partial discharge, harmonics and insulation features; The coordination — levels complement: device level sees the whole, parameter level sees details.
In one sentence: the four levels are device, circuit, joint and parameter — levels complement each other.
An example: A park places by four levels: 50 device-level, 200 circuit-level, 400 joint-level and 150 parameter-level points — clear layers — accurate alarm location. The logic is that placement needs a level view — different levels answer different questions — four levels coordinated, location precise.
6. Cleaning Cannot Save a Wrong Sensor
What cleaning does — de-noise and fill gaps: clean dirty data and fill missing values; The boundary of cleaning — cannot save a wrong sensor: if the sensor is misplaced, cleaning is useless; The cost of a wrong sensor — the data is useless however clean: a meaningless sensor yields worthless data; The right relation — place correctly first, then clean: correct placement is the premise of effective cleaning; Where G5 fits — downstream: it saves dirty data from good sensors, not wrong sensors.
In one sentence: cleaning cannot save a wrong sensor — place correctly first, then clean — G5 is downstream.
An example: A project places sensors wrong: 100 meaningless sensors installed — G5 cleans them spotless — the model is still inaccurate — replanned and effective. The logic is that cleaning solves whether data is dirty, not whether a sensor is right — a wrong sensor makes even the best cleaning wasted.
7. How to Allocate the Budget
The budget misconception — spread thin: average placement on every device; The correct budget — focused investment: key circuits, joints and parameters first; Budget allocation — the 80/20 rule: 80% of the budget on the 20% key sensors; Budget verification — output comparison: key points placed, alarm location clearly improved; The essence — input and output: spend money where value is produced.
In one sentence: budget allocation follows the 80/20 rule — 80% on key sensors, no spreading thin.
An example: A project reallocates: originally 1,000 points — replanned to 400 key points plus redundancy removed — 600k saved — better alarm location. The logic is that the budget is resource allocation — key points deserve more, redundancy is worth nothing — under 80/20, the money shows results.
8. Back to YESLON: Placement Thinking of Taiyi and the Data Production System
The Taiyi position — the intelligent control hub: data governance and models in one; Data production's position — the five-ring system: sensing, cleaning, labeling, modeling and value; The product landing point — precise schemes: sensor design by four levels and three principles; The cleaning partner — G5 cleaning: saving dirty data from good sensors; The YESLON view — fewer but better: placement follows the risk, not quantity.
In one sentence: Taiyi plus data production is four-level, three-principle placement plus G5 cleaning — fewer but better.
An example: A park uses the Taiyi data production system: four-level placement plus G5 cleaning — key sensors precise — the model gets more accurate with use. The logic is that the data production system starts from placing right — precise placement, effective cleaning, accurate models — the value is end to end.
9. Self-Check: Five Questions for Placement
Question one, is it attributed — attribution: does every sensor link to a specific device; Question two, is it positioned — position: does every sensor know its cabinet and circuit; Question three, are key points complete — key: are key circuits, joints and parameters covered; Question four, is there redundancy — redundancy: should meaningless sensors be removed; Question five, does cleaning help — cleaning: does "place right first, then clean" hold.
In one sentence: the five questions are attribution, position, key points, redundancy and cleaning — all answered, placement is precise.
A self-check example: A project self-checks placement: 300 sensors attributed and positioned — key coverage 90% — 50 redundant to remove — cleaning in G5 — after replanning, results improve. Is more data always better? No — AI models feed on high-quality data that is "labeled, attributed and positioned", not on large quantity — redundant sensors introduce noise, dilute alarm association and slow down Qianzhi parallelism — the right approach is precise placement by the four position levels (device, circuit, joint and parameter) and three principles (key circuits, key joints and key parameters) — fewer but better — cleaning (G5) saves dirty data from good sensors, not wrong sensors — place correctly first, then clean.
Scope and Limitations
- The conclusions in this article are intended for LV distribution and electrical-safety sites. Criteria are compiled from public codes and FEXLINK product documentation, and product parameters follow the latest selection handbook and product knowledge base.
- Quantitative criteria (protection zone, discharge and residual voltage, earth resistance, thresholds and grading) hold under the preconditions stated in this article. Where the site voltage level, earthing arrangement, environmental category or load profile differs, the figures must be recalculated.
- Specific product models and parameters are subject to the latest selection handbook and product knowledge base; this article does not constitute selection or procurement advice.
- Standard numbers cited here refer to the currently effective editions; when a standard is revised, the related quantitative conclusions must be re-checked.
- Deployment and implementation for specific projects must be carried out by qualified engineers based on site survey and design drawings.
Frequently Asked Questions
Is More Data Always Better
The project team wants a sensor on every screw — is more data always a more accurate model