Direct Answer
Three monitoring devices differ in price at the same installation position — which one should you choose? Choose by the monitoring goal: use the SFA for energy metering, leakage and temperature only; use the SFB when you need three-phase imbalance (adds phase); use the SFE when you need harmonics and power quality (adds 2nd-31st harmonics); same architecture, same installation, matched by current specification and networking. SFA, SFB and SFE are three devices of one family: the same installation, the same common features — the difference is "what more it measures" — set the monitoring goal first, then the model, and never buy an unnecessary configuration.
A scene: in one switchroom, the same row of cabinets needed monitoring devices: ordinary feeders only needed energy metering, important feeders needed three-phase imbalance, core feeders needed harmonics — three models installed separately: SFA for ordinary feeders, SFB for important feeders, SFE for core feeders — choose the model by the monitoring goal, and spend money where it counts.
1. The Relationship of the Three: One Family, Different Levels
The family relationship — SFA, SFB and SFE are three devices of one family: the same architecture and installation — the difference is the capability level; The progression of levels — the SFA is the basic model: energy metering, leakage and temperature; the SFB adds phase: three-phase imbalance; the SFE adds harmonics: power quality — levels rise step by step; The meaning of the same architecture — the three share the same installation and wiring — changing models does not require changing the cabinet or the wiring; The selection logic — set the monitoring goal first, then the level: the goal decides which model — the price difference corresponds to "what more is measured".
In one sentence: the three = one family with different levels + same architecture, same installation + SFA metering / SFB phase / SFE harmonics — set the monitoring goal first, then the level.
A family example: in one project, the same batch of cabinets: SFA basic models installed first, then two cabinets upgraded to the SFE — the cabinet and wiring were unchanged; replacing the module was the upgrade. The value of the same architecture is "change models without changing cabinets" — level upgrades need no rework — three in one family keeps the selection pressure low.
2. The SFA: The Energy Metering Model
The positioning of the SFA — the basic monitoring device: energy metering + leakage current + temperature — the standard for ordinary feeders; Energy metering — voltage, current, power and energy: full three-phase energy coverage — billing energy is accurate; Leakage and temperature — leakage current monitoring + temperature monitoring: electrical safety hazards known early — even the basic model carries safety monitoring; Applicable scenarios — ordinary distribution feeders: needing only energy metering and basic safety monitoring — the SFA offers the best value.
In one sentence: the SFA = energy metering + leakage + temperature — the standard for ordinary feeders — for energy metering and basic safety monitoring only, the SFA is the best value.
An SFA example: the lighting feeders of one campus needed only energy metering and leakage monitoring — the SFA was installed — functions just enough, no waste. The SFA is the "enough" model — energy, leakage and temperature in three — ordinary feeders use it without wasting the budget.
3. The SFB: The Three-Phase Model
The positioning of the SFB — the three-phase monitoring device: adds phase monitoring on top of the SFA — to see three-phase imbalance; Phase monitoring — three-phase voltage/current phase: imbalance, phase-sequence anomalies — unbalanced three-phase loads known early; The meaning of three-phase imbalance — imbalance causes zero-sequence current and neutral overheating — important feeders must see it; Applicable scenarios — important distribution feeders: motors, server rooms, large-load feeders — the SFB for three-phase status.
In one sentence: the SFB = the SFA + phase monitoring — to see three-phase imbalance — important feeders (motors/server rooms/large loads) use the SFB.
An SFB example: the three-phase current imbalance of a server-room feeder was 25% — the SFB detected it, load distribution was adjusted — the imbalance dropped to 8%. What the SFB measures more is "phase" — imbalance and phase-sequence anomalies — three-phase problems found early, and important feeders cannot do without it.
4. The SFE: The Power Quality Model
The positioning of the SFE — the power quality monitoring device: adds harmonic monitoring on top of the SFB — to see power quality; Harmonic monitoring — 2nd-31st harmonics: harmonic content and distortion rate — harmonic problems quantified and visible; The power quality scenario — feeders with many variable-frequency drives and rectifier loads: large harmonics, poor power quality — core feeders must see it; Applicable scenarios — core distribution feeders: VFD, rectifier and sensitive loads — the SFE to watch power quality.
In one sentence: the SFE = the SFB + 2nd-31st harmonics — the power quality model — core feeders (VFD/rectifier/sensitive loads) use the SFE.
An SFE example: the harmonic distortion of one VFD feeder was 12% — the SFE detected it, filtering was added — the distortion dropped to 5%. What the SFE measures more is "harmonics" — 2nd-31st harmonics and distortion rate — with power quality visible, core feeders are protected.
5. Choosing Among the Six Current Specifications
The meaning of the specifications — all three models have six current specifications: from 3×5A to 3×1000A — the specification matches the primary current / transformer; Choosing the specification — choose by the feeder current: small feeders use small specifications, large feeders use large ones — the specification matches the secondary side of the transformer; A common misconception — is bigger always better? No — the specification must match the actual current — a large specification with a small current wastes accuracy; Specification and the transformer — direct-through / transformer-matched configurations: the specification corresponds to the transformer ratio — a mismatch makes the metering inaccurate.
In one sentence: the current specification = six levels from 3×5A to 3×1000A + chosen by the feeder current + matched to the transformer — with the right specification, the metering is accurate.
A specification example: a cabinet feeder had a rated current of 400A — the 3×400A specification was chosen with the transformer — the metering was accurate. Bigger is not always better — matching the feeder current is right — a large specification with a small current discounts the accuracy.
6. Choosing Between -E Ethernet and -G 4G Uplink
The meaning of the uplink — -E means Ethernet uplink, -G means 4G uplink — different networking; -E Ethernet — where network cable exists, use -E: stable, fast, low cost — the first choice for campus internal networks; -G 4G — where no network cable exists, use -G: wireless, fast deployment — the first choice for dispersed and remote points; Choosing the uplink — first check whether the point has network: with network use -E, without use -G — the networking follows the site conditions.
In one sentence: the uplink = -E Ethernet / -G 4G — with network use -E, without use -G — choose the networking by the site conditions.
An uplink example: a cabinet in one campus had network cable — the -E Ethernet uplink was chosen; dispersed points in a plant had no network — the -G 4G uplink was chosen — each in its own place. The uplink follows the site — Ethernet where there is network, 4G where there is not — no agonizing over networking; the site conditions decide.
7. Common Features and the Upgrade Path
Common features — the three share: OLED display, leakage current, temperature and digital I/O — the basic capabilities are the same; The upgrade path — install the SFA first and upgrade to the SFE later — is it feasible? Yes — same architecture, same installation — replacing the module is the upgrade; Upgrade notes — confirm before upgrading: the installation position, wiring and current specification are the same — after confirmation, the upgrade is worry-free; The value of the upgrade — start with the basic model, upgrade as needed — invest in stages, add features as needed.
In one sentence: common features = OLED + leakage + temperature + digital I/O + the path from SFA to SFE — same architecture, replace the module to upgrade — invest in stages, add features as needed.
An upgrade example: a plant first installed the SFA for energy metering — later the core feeder needed harmonics — replaced with the SFE module as the upgrade; the cabinet and wiring were untouched. The upgrade path is "SFA first, SFE later" — start with the basic model, upgrade on demand — investment goes in steps, features follow the requirements.
8. Back to FEXLINK: How to Configure the Three as One Set
The FEXLINK SFA, SFB and SFE monitoring devices (SFA-10011~10061, SFB-11011~11061, SFE-11111~11161) share the same architecture, installation and common features — matched by the importance of the feeder. The selection checklist: ① set the monitoring goal first — energy/three-phase/harmonics → ② choose the model next — SFA metering, SFB adds phase, SFE adds harmonics → ③ match the current specification — six levels from 3×5A to 3×1000A by the feeder current → ④ choose the uplink — -E Ethernet with network, -G 4G without → ⑤ reserve the upgrade — SFA first then SFE, replace the module to upgrade — three models matched, one set complete.
One summary: how to choose among the SFA/SFB/SFE = model by the monitoring goal + current specification matched + networking paired — the SFA meters energy, the SFB adds phase and the SFE adds harmonics — same architecture, same installation, change models without changing cabinets. The three are "three levels of one family" — the goal sets the model, the specification matches the current and the networking follows the site — with the right level, money is spent where it counts.
One reminder: when hesitating over which model to install at one position, do not ask "which is best" first — ask "what does this feeder need to measure" — energy only, use the SFA; three-phase needed, use the SFB; harmonics to watch, use the SFE — with the goal clear, the model is naturally clear. Selection is not choosing "the most expensive" but "the most right" — the monitoring goal sets the model, and the price difference goes to the features needed.
Scope and Limitations
- The conclusions in this article are intended for LV distribution and electrical-safety sites. Standard numbers (GB/T 14549-1993) refer to their currently effective editions, and product parameters follow the latest FEXLINK selection handbook and product knowledge base.
- Quantitative criteria (protection zone, discharge and residual voltage, earth resistance, thresholds and grading) hold under the preconditions stated in this article. Where the site voltage level, earthing arrangement, environmental category or load profile differs, the figures must be recalculated. Specific configurations involving SFA-10011~10061、SFB-11011~11061、SFE-11111~11161 should be verified against actual circuit parameters.
- Specific product models and parameters are subject to the latest selection handbook and product knowledge base; this article does not constitute selection or procurement advice.
- Standard numbers cited here refer to the currently effective editions; when a standard is revised, the related quantitative conclusions must be re-checked.
- Deployment and implementation for specific projects must be carried out by qualified engineers based on site survey and design drawings.
Frequently Asked Questions
SFA vs. SFB vs. SFE: Meter-Only, Three-Phase, or Power-Quality?
Three monitoring devices differ in price at the same installation position — which one should you choose